SurfaceWorks Pricing Guide September 2025

ORIGINAL LINES SURFACEWORKS PRICING GUIDE

HOW TO ORDER PANEL SYSTEMS WORKSURFACES

Model Number, Finishes, Options

Overview Panel Systems Worksurfaces are constructed specifically for use in conjunction with office panel systems. Worksurfaces are 1/8" undersized and the edge selection includes "F-Series" urethane edges featuring flat profile edgeband on non-user sides to allow for ease of adjacent placement.

Universal Flat Plates* Universal Flat Plates are used to create a fixed connection between two Worksurfaces. *Flat Plates are accessories to be ordered on a separate line item, shipped loose and field installed. Screws are included. Universal Flat Plate

Featured Grommet Option: G23 Rectangular grommets with covers are available in 1, 2 or 3 grommets per Worksurface; placement using codes as per diagram below.

G23 Rectangular Grommet with Cover rectangle Grommet

Model Number

Universal Flat Plates

Example: WS.L.2442

HTO-WS-1 Colors & Finishes Click here to review all currently available product finishes. Top Edge Treatment Standard Edge Treatment. . . . . .... see pricing pages Other Edge Treatment. . . . . . . ....... quote required Top Edge Finish Standard Edge Color . . . . . . . . . . . . . ............. std Non-Standard Edge Color. . . . . . ..... quote required Top Surface Finish Group 1 Laminate. . . . . . . . . . . . . . ............... std Group 2 Laminate. . . . . . ....... see upcharge column Other Laminate/Material . . . . . . ...... quote required Stiffeners* Stiffeners are recommended to minimize sagging on Worksurfaces that have unsupported spans of 45" to 60", once installed. The maximum unsupported span should not exceed 60". Optimal stiffener placement is in the center, directly between the base plates (or other supports), however, it can be placed up to 6” off the center. If the stiffener must be placed further off center, it is recommended to install two stiffeners, placed parallel. If the Worksurface is 36" or wider, two parallel stiffeners are recommended. *Stiffeners are accessories to be ordered on a separate line item, shipped loose and field installed. Screws are included.

MODEL NUMBER

Worksurface Grommet Placement Worksurface Grommet Placement Rectangle L C R D-Shape C R L C

AP

D-Corner-L D-Corner-R

R

C

Pricing AXH.UFP.13 0.8"x 2.6" Flat Plate. . . . . . . ....... $12 AXH.UFP.23 2.25"x 3" Flat Plate. . . . . . . . . . . . . . .$12 AXH.UFP.35 3"x 5" Flat Plate. . . . . . . . . ........ $25 Wire Pass-Through Scallop Option Scallops provide a pass-through for cords for worksurfaces placed against a wall or panel system. They are 6” wide by 1-1/4” deep and shaped into the back side(s) of worksurfaces/tops. Scallops are priced per unit, regardless of the quantity of scallops. See standard Scallop placement chart below.

L

Corner Straight

Corner Curved

Ext. Corner-L

Ext. Corner-R

L

C

R

C

L

C

L

C

R

L

R

R

Pricing C:

1 grommet, CTR placement (default) . . .. + $36 1 grommet, LH placement . . . . . . ....... + $36 1 grommet, RH placement. . . . . . ....... + $36 2 grommets, L & R placement (default). .. + $72 2 grommets, LH & CTR placement . . . ... + $72 2 grommets, CTR & RH placement . . . ... + $72 LCR: 3 grommets, LH, CTR & RH placement.. + $108 Other Grommets. . . . . . ....... see accesories section L: R: LR: LC: CR:

Scallops Scallops

Scallop placement

STIFFENER

Standard Scallop Placement

60” Unsupported Span with Stiffener

Scallop Placement

Scallop Quantity

Non-User Side Dimension

24x96 Top/Worksurface with unsupported span of 60” 54” Stiffener recommended 60” unsupported span

20” from each end

2

70” or greater

Center

1

30” to 69”

Stiffener

n/a

none

less than 30”

Pricing AXH.STF.45 45" Stiffener (for span of 45"-54"). . . $67 AXH.STF.54 54" Stiffener (for span of 54"-60"). . . $76

Pricing SCS

Scallops, Standard Placement . . . . . ..... + $33 SCN Scallops, Non-standard Placement. . . ... + $49

2 74