SurfaceWorks Pricing Guide September 2026

PANEL SYSTEMS WORKSURFACES HOW TO ORDER Model Number, Finishes, Options, Accessories

SURFACEWORKS PRICING GUIDE

Overview Panel Systems Worksurfaces are constructed specifically for use in conjunction with office panel systems. Worksur faces are 1/8" undersized and the edge selection includes "F-Series" urethane edges featuring flat profile edgeband on non-user sides to allow for ease of adjacent placement. Model Number Example: WS.L.2442 Colors & Finishes Top Edge Treatment Standard Edge Treatment . . . . . . . . .see pricing pages Other Edge Treatment . . . . . . . . . . . . . . quote required Top Edge Finish Standard Edge Color . . . . . . . . . . . . . . . . . . . . . . . . . std Non-Standard Edge Color . . . . . . . . . . . quote required Top Surface Finish Group 1 Laminate . . . . . . . . . . . . . . . . . . . . . . . . . . . . std Group 2 Laminate . . . . . . . . . . . . . . . .see pricing pages FENIX® Super Matte Laminate . . . . . . . quote required Forbo Funiture Linoleum . . . . . . . . . . . .quote required Other Laminate/Material . . . . . . . . . . . .quote required Stiffeners Stiffeners are recommended to minimize sagging on Work surfaces that have unsupported spans of 45" to 60", once installed. The maximum unsupported span should not exceed 60". Optimal stiffener placement is in the center, directly between the base plates (or other supports), however, it can be placed up to 6” off the center. If the stiffener must be placed fur ther off center, it is recommended to install two stiffeners, placed parallel. If the Worksurface is 36" or wider, two par allel stiffeners are recommended. Stiffeners are accessories to be ordered separately and field installed. Screws are included.

Universal Flat Plates Universal Flat Plates are used to create a fixed connection between two Worksurfaces. Flat Plates are accessories to be ordered separately and field installed. Screws are included.

G23 Grommet Option G23 Rectangular grommets with covers are available in 1, 2 or 3 grommets per Worksurface; placement using codes as per diagram below.

G23 Rectangular Grommet with Cover

Universal Flat Plates

Worksurface Grommet Placement Rectangle L C R D-Shape C

D-Corner-L D-Corner-R

Pricing AXH.UFP.13 0.8"x 2.6" Flat Plate . . . . . . . . .. . . . . $13 AXH.UFP.23 2.25"x 3" Flat Plate . . . . . . . . . . . . . . . $13 AXH.UFP.35 3"x 5" Flat Plate . . . . . . . . . . . .. . . . . $26 Wire Pass-Through Scallop Option Scallops provide a pass-through for cords for worksurfaces placed against a wall or panel system. They are 6” wide by 1-1/4” deep and shaped into the back side(s) of work surfaces/tops. Scallops are priced per unit, regardless of the quantity of scallops. See standard Scallop placement chart below.

R

C

L

C

L

R

Corner Straight

Corner Curved

Ext. Corner-L

Ext. Corner-R

L

C

R

C

L

C

L

C

R

L

R

R

Pricing C 1 grommet, CTR placement (default) . . . . . .+ $38 L 1 grommet, LH placement. . . . . . . . . . . . . . .+ $38 R 1 grommet, RH placement. . . . . . . . . . . . . . .+ $38 LR 2 grommets, L & R placement (default) . . . .+ $76 LC 2 grommets, LH & CTR placement . . . . . . . .+ $76 CR 2 grommets, CTR & RH placement. . . . . . . .+ $76 LCR 3 grommets, LH, CTR & RH placement . . .+ $114 Non-Standard Placement. . . . . . . . . . . . quote required Other Grommets. . . . . . . . . . . . . . . . . . . quote requried

Scallops

Standard Scallop Placement

Stiffener

Scallop Placement

Scallop Quantity

Non-User Side Dimension

20” from each end

2

70” or greater

Center

1

30” to 69”

n/a

none

less than 30”

Pricing SCS Scallops, Standard Placement . . . . . . . . . . . .+ $35 SCN Scallops, Non-standard Placement. . . . . . . .+ $52

60” Unsupported Span with Stiffener

24x96 Top/Worksurface with unsupported span of 60” 54” Stiffener recommended 60” unsupported span

Stiffener

Pricing AXH.STF.45 45"Stiffener..................... $71 AXH.STF.54 54"Stiffener..................... $80

268